Menu
EUR
Nu 10% korting op het hele assortiment! Gebruik code: BLACK10 *Niet geldig op Magnum-producten
Electric underfloor heating not warming up? Causes and solutions

Electric underfloor heating not warming up? Causes and solutions

By: H.G. Voortman Comments: 0

Is your electric underfloor heating not warming up? Does the thermostat indicate that the heating is on while the floor stays cold? Fortunately, this does not necessarily mean the heating mat is faulty. The cause is often the thermostat, floor sensor, wiring or settings. It is therefore worth carrying out a few checks before assuming your electric underfloor heating is defective.

This article explains what to check, step by step, when electric underfloor heating does not work or does not get warm enough.

Electric underfloor heating stays cold: where should you start?

Do not immediately replace components. First work through the possible causes systematically.

We recommend this order:

  1. Check that the thermostat is switched on.
  2. Check that it is actually calling for heat.
  3. Check the thermostat settings.
  4. Check the wiring connections.
  5. Check the floor sensor.
  6. Measure the heating mat's resistance with a multimeter.
  7. Only then investigate whether the thermostat itself may be faulty.

Each step is explained below.

1. Check the underfloor heating thermostat

If electric underfloor heating is not warming up, the thermostat is the first place to look.

Is the display on? Temporarily increase the target temperature a few degrees above the measured temperature. The thermostat should then indicate that it is heating. Also check that no setting is preventing it from switching on, such as a weekly programme, holiday mode or maximum floor temperature limit.

Some thermostats can control the room temperature, floor temperature or a combination of both. An incorrect setting can leave the floor cold even when nothing is technically broken.

2. Check that the thermostat is wired correctly

Incorrect wiring is another possible reason why electric underfloor heating does not work. Many thermostats use terminals such as:

  • L and N: the thermostat's power supply.
  • L1 and N1: the connection to the electric heating mat.

The floor sensor has separate terminals. The exact terminal layout differs between thermostats, so always consult the wiring diagram for your particular model. Our website also has a detailed guide:

View the thermostat wiring guide

Warning: never work on wiring while it is live. If you are unsure about the electrical connections, consult an electrician.

3. Check that all connections are secure

Sometimes the solution is surprisingly simple. Check that all wires are securely fixed in the thermostat terminals. A loose or poor connection can make the thermostat appear to work normally while the heating mat receives no power. Carefully check the connections for:

  • the power supply;
  • the heating mat;
  • the floor sensor.

If everything is secure but the floor remains cold, the next important step is to test the heating mat.

4. Test electric underfloor heating with a multimeter

This is one of the most important checks when electric underfloor heating will not warm up. A multimeter measures the heating mat's resistance, which helps establish whether the heating cable appears electrically intact.

The main measurement is between the mat's brown and blue wires. Compare the reading with the specified resistance for that particular mat. It is also necessary to check that there is no unwanted electrical connection between the supply conductors and earth.

How do you test electric underfloor heating?

We have a separate step-by-step guide and video called “Measuring electric underfloor heating with a multimeter”:

View the testing guide

The guide explains:

  • how to set the multimeter;
  • which wires to measure between;
  • which measurements to take;
  • how to check the resistance reading;
  • what to do if the reading differs from the specified value.

Important: never measure a heating mat's resistance while it is connected to a live supply.

5. Is the resistance correct? Check the thermostat and sensor

If you test the mat correctly and the resistance matches the specified value, this is a useful indication that you should investigate the controls and wiring next. Check the thermostat and floor sensor again. The floor sensor tells the thermostat the floor temperature. If it reports an incorrect temperature, the thermostat may think the floor is already warm enough. As a result, it may not switch on or may switch off too soon, leaving the floor cold or insufficiently warm.

Some thermostats display an error message when there is a sensor problem. On other models, the cause is less obvious.

6. Can an electric underfloor heating thermostat fail?

Yes. It is not especially common, but it is possible. A thermostat may have a working display while its internal relay no longer switches power to the heating mat correctly. This is why we advise against immediately buying a replacement thermostat.

First check:

  • the settings;
  • the electrical wiring;
  • the floor sensor;
  • the heating mat's resistance;
  • all contacts and connections.

If these are correct, the thermostat may need further investigation.

7. The floor gets warm, but not warm enough

Does the floor become slightly warm, but take a very long time to heat up or fail to reach the required temperature? Other possible causes include:

  • insufficient insulation beneath the heating;
  • a cold subfloor;
  • insufficient installed wattage per m²;
  • incorrect thermostat settings;
  • a maximum floor temperature set too low;
  • a thick floor covering;
  • high heat loss from the room.

Insulation under electric underfloor heating is particularly important. Without a suitable insulating layer, some heat can travel downwards instead of towards the floor surface. The heating may work correctly but take longer to warm the floor and room.

8. How quickly should electric underfloor heating warm up?

This depends on the floor build-up. A thin heating mat installed directly beneath tiles responds much faster than a system beneath a thick layer of levelling compound or screed. The insulation, wattage per square metre and temperature of the structural floor also matter.

Do not expect every electric underfloor heating system to feel warm within a few minutes. Read more in our article about electric underfloor heating warm-up times.

If the heating used to work properly but the floor suddenly stays completely cold, carry out the checks above.

9. How do I know whether my underfloor heating is faulty?

A cold floor alone does not prove the heating mat is faulty. This is why testing is important. If the measurements differ from the specified values, or an unwanted connection to earth is detected, the system may be damaged or defective. Stop using it and have the fault investigated.

If the measurements are correct, look elsewhere: the thermostat, sensor, wiring or settings.

10. What if the electric underfloor heating really is faulty?

A confirmed fault does not automatically mean that the entire existing tiled floor must be removed. Our Pro-mat Pro-Series electric underfloor heating may offer an alternative.

At approximately 2–3 mm thick, Pro-mat Pro-Series is particularly thin and can, in many situations, be installed over existing tiles.

The existing floor can remain as the substrate, with new electric underfloor heating and a new floor finish installed above it. This can save substantial demolition work.

Whether this is suitable depends on the condition of the substrate, available build-up height and intended floor covering.

Electric underfloor heating not warming up? Our checklist

Start by checking:

  • Is the thermostat on?
  • Is it actually calling for heat?
  • Are the settings correct?
  • Are L and N connected correctly?
  • Is the heating mat connected correctly?
  • Is the floor sensor connected correctly?
  • Are all connections secure?
  • Is the heating mat's resistance correct?
  • Is there any unwanted connection to earth?
  • Is the thermostat working correctly?

Do not immediately start removing tiles if your electric underfloor heating stops working. Testing and checking first can avoid unnecessary work and expense.

Still need help? Contact us

If you have checked these points but the floor still does not warm up, contact us. We can help you work out the likely cause.

If possible, have these details ready:

  • heating mat make and model;
  • mat area and wattage;
  • measured resistance;
  • thermostat model;
  • any error message.

If the existing underfloor heating is genuinely faulty, we can also advise on a new, extra-thin system that can often be installed with minimal additional build-up height.


Comments (0)

There are no comments yet, be the first one to comment
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
Order for another €150,00 and receive free shipping
0
Compare
Start comparison

Leave a comment

Your email address will not be published
This product has been added to your cart