Menu
EUR
Nu 10% korting op het hele assortiment! Gebruik code: BLACK10 *Niet geldig op Magnum-producten

Electric underfloor heating running costs: electricity use explained

By: H.G. Voortman Comments: 0

What does electric underfloor heating cost in electricity?

A 10 m² system rated at 150 W/m² has a maximum power of 1.5 kW. At an illustrative electricity price of €0.30/kWh, one full hour of continuous heating costs €0.45. Your own tariff may differ. The thermostat switches heating off once the set temperature is reached, so actual consumption depends on its run time.

Power and energy are different

Watts (W) describe maximum electrical power; kilowatt-hours (kWh) measure the energy you pay for. A higher-powered heater running briefly can use less energy than a smaller one running for longer. Heat loss from the room, including downward losses, determines how much heat must be replaced. Installed power influences warm-up speed and whether the system can meet demand.

Calculate maximum consumption

Heated area × watts per m² = total power. At 150 W/m²: 5 m² = 750 W; 10 m² = 1,500 W; 15 m² = 2,250 W; 20 m² = 3,000 W. Divide by 1,000 to obtain kW. Multiply by actual heating hours to obtain kWh, then by your price per kWh.

For 1.5 kW: one full heating hour uses 1.5 kWh and costs €0.45 at €0.30/kWh. Two hours cost €0.90, four €1.80, six €2.70 and eight €3.60. These assume uninterrupted heating at full power.

Maximum cost per full heating hour

The following amounts use the example tariff of €0.30/kWh. They are not annual or daily predictions.

Area 100 W/m² 150 W/m² 200 W/m²
5 m² € 0.15 € 0.23 € 0.30
10 m² € 0.30 € 0.45 € 0.60
15 m² € 0.45 € 0.68 € 0.90
20 m² € 0.60 € 0.90 € 1.20

Duty cycle: how often heating actually runs

The thermostat may be enabled all day while the heating element runs only part of that time. This proportion is its duty cycle. Building insulation, insulation below the heater, setpoint, outdoor temperature, floor finish, output and use as primary or supplementary heating all affect it.

For 10 m² at 150 W/m², an eight-hour enabled period and €0.30/kWh:

Duty cycle Daily consumption Daily cost
100% 12 kWh € 3.60
50% 6 kWh € 1.80
30% 3.6 kWh € 1.08
20% 2.4 kWh € 0.72

These are scenarios, not predicted savings. A poorly insulated space may require continuous heating; another room may need much less.

Measure your own consumption

Where supported, a thermostat’s heating-hours log can provide an estimate: actual heating hours × kW × tariff. Not every WiFi thermostat reports reliable heating hours or metered energy. A dedicated kWh meter installed by an electrician gives the clearest measurement. Smart-meter comparisons on days with similar weather can indicate use, but other appliances affect the result. Measure for at least a representative week.

Choosing 100, 150 or 200 W/m²

100 W/m² may suit very well-insulated rooms if the available heated area can meet the calculated heat loss. For 10 m² its maximum draw is 1 kW, or €0.30 per full hour at the example tariff.

150 W/m² is widely used. The Pro-mat Pro-Series is a popular option. For 10 m² the maximum is 1.5 kW, or €0.45 per full hour. View the Pro-Series set.

200 W/m² can provide more output or faster warm-up where the floor and installation allow it. For 10 m² the maximum is 2 kW, or €0.60 per full hour.

Does 200 W/m² always use twice as much energy?

No. Its maximum power is twice that of 100 W/m², but a higher output can reach the setpoint sooner and switch off earlier. For comparable conditions, heat demand matters more than installed power alone. Too little output may fail to warm the room even while running continuously. That does not automatically mean it uses more total energy than a higher-powered system; it means it cannot meet the demand.

Insulation directly below the heating

Heat flows both upward and downward. Insulation close below the heater can reduce heat transfer into the supporting floor and improve response. Pro-Board XPS is one option; the appropriate thickness and construction depend on the project. Compare insulation boards.

A possible build-up for suitable glued PVC is: existing screed → bonded 10 mm Pro-Board XPS → electric heating → approved levelling compound → compatible PVC. Keep the covering thickness within the instructions for the heater, compound and flooring. Do not reduce required cover merely to improve warm-up time.

The floor finish matters

Tiles and natural stone transfer heat readily. Suitable PVC and laminate can also work, subject to temperature and thermal resistance limits. Avoid unnecessary insulating layers above the heating, thick rugs and closed furniture that trap heat. This differs from the specified insulation below the heater.

Programming and solar panels

Set a weekly programme that suits room use. Allow for the actual warm-up time; adaptive start is available only on thermostats that support it. A lower setpoint during absence reduces heat loss. Whether to switch off completely depends on comfort, response time and absence duration. Reheating does not by itself cancel the savings from a lower temperature.

Time-of-use or dynamic tariffs may make some hours cheaper. Check whether shifting heat increases losses or reduces comfort. Solar panels can help when production overlaps demand, but winter heating demand is highest when solar generation is lower. Do not assume free heating for the entire season.

Electrical load on larger areas

At 230 V, a 16 A circuit has a theoretical maximum of approximately 3,680 W. Other loads, installation conditions and local rules also matter. Examples: 15 m² × 200 W/m² = 3,000 W; 20 m² × 200 W/m² = 4,000 W; 25 m² × 150 W/m² = 3,750 W.

An electrician must size the protection and circuits and perform the connection. Larger installations may need separate circuits, thermostats or suitable load modules. A load module does not increase a circuit’s permitted capacity. The Dutch circuit example is not a substitute for local installation requirements.

Electric or water-based underfloor heating?

Water-based heating often sits within a larger thermal mass and responds more slowly, though low-profile designs also exist. Thin electric systems with insulation directly below can respond quickly. Running cost depends on the heat source: a gas boiler and a heat pump have very different characteristics. Compare the complete installation, annual demand, tariffs and maintenance.

Your own cost formulas

Maximum cost per full heating hour = m² × W/m² ÷ 1,000 × electricity price per kWh. Examples: 8 × 150 ÷ 1,000 × €0.30 = €0.36; 12 × 100 ÷ 1,000 × €0.30 = €0.36.

Estimated daily cost = kW × enabled hours × duty cycle × tariff. Example: 1.5 × 8 × 30% × €0.30 = €1.08. A duty cycle must be measured or treated as a scenario, not assumed as a guarantee.

Frequently asked questions

How much electricity per m²? While switched on, 100, 150 and 200 W/m² use 0.1, 0.15 and 0.2 kWh per m² in one hour respectively.

Is 100 W/m² sufficient? Only if the installed area and permitted floor temperature can meet the room’s heat demand.

Can XPS reduce use? It can limit downward heat transfer; the improvement depends on the entire build-up.

Why is the floor cold? Check the settings, sensor, electrical supply and installation rather than assuming the power rating is the cause. Have electrical faults inspected by a qualified professional.

Advice for your home

Choose by insulation, usable area, desired temperature, floor construction and heat demand, rather than watts alone. Ask Vloer-verwarming.com for advice on output, insulation and the complete floor build-up.


Comments (0)

There are no comments yet, be the first one to comment
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
Order for another €150,00 and receive free shipping
0
Compare
Start comparison

Leave a comment

Your email address will not be published
This product has been added to your cart