Is electric underfloor heating safe?
Yes, electric underfloor heating is safe, provided the system suits the application, is installed correctly and is properly controlled. Safety does not come from a single approval mark or a single setting. The heating, the electrical connection, the floor build-up and the way you use it all have to work together.
Questions about safety usually cover three different things: radiation, fire risk and a floor that gets too hot. Each needs its own answer. An RCD, for example, protects against an electrical fault, but it will not stop heat building up under a thick rug.
What radiation does electric underfloor heating give off?
First of all, heat. A warm floor gives off part of that heat as infrared radiation, just like a floor heated by warm water.
On top of that, every electrical system creates electric and magnetic fields, or EMF for short. On the UK mains these are low-frequency fields at 50 hertz. That is non-ionising radiation, which is something completely different from X-rays. Even so, "non-ionising" does not tell the whole story: the strength of the field and the distance from the source matter too.
Is EMF from underfloor heating harmful?
Low-frequency fields from mains wiring and appliances have been studied extensively. There is still uncertainty about long-term effects. A statistical link has been found between long-term exposure to raised low-frequency magnetic fields and childhood leukaemia. The WHO's International Agency for Research on Cancer (IARC) therefore classifies these fields as "possibly carcinogenic". A statistical link, however, is not proof of cause and effect.
So this research does not prove that underfloor heating makes you ill. Nor is it a basis for promising that every system is risk-free in all circumstances. How strong the field of a particular mat is depends on the cable design, the current and the distance. In twin-conductor cables, where the outgoing and return conductors run close together, the magnetic fields partly cancel each other out.
Terms such as "radiation-free" or "EMF-free" mean little without measurements. Do they refer to a low measured field strength, an earthed screen, or simply the absence of a wireless transmitter? If you want to compare systems, ask for a test report for the exact product, including measuring distance and conditions. Note that a WiFi thermostat is a separate source of radio signals and has nothing to do with the heating in the floor.
Can electric underfloor heating cause a fire?
As with any electric heating system, a defect or incorrect installation can be dangerous. A correctly installed system is not a fire risk in itself, but it must be used the way it was designed. A mat designed to be embedded in tile adhesive, for example, should not be laid loose under a rug.
| Cause | What can go wrong? | How to prevent it |
|---|---|---|
| Damaged cable or insulation | Electrical fault or local damage | Test before and after laying, before the floor is closed |
| Crossing, overlapping or doubled-up cables | Local heat build-up | Follow spacing and layout plan, never double up offcuts |
| Shortened heating cable | Resistance and output change | Never cut the heating cable (the cold lead is a different matter) |
| Loose or unsuitable connection | Heat at the terminal | Suitable components and correct fitting |
| Blocked heat output | Local overheating | Take furniture and floor coverings into account |
| Wrong probe setting | Floor warmer than intended | Set the right control mode and temperature limit |
How does a floor overheat?
The heating produces heat, and the floor has to pass it on to the room. If that is blocked in one spot, the temperature there rises further than on an open part of the floor. Think of a thick rug, a mattress on the floor or a cupboard without legs.
What is allowed depends on the system and the full floor build-up. A rug that is fine on one floor may be too much on another. That is why you do not lay heating under fitted units. Output per m² says little on its own either: 200 W/m² is not unsafe and 100 W/m² is not automatically safe. The output has to match the room, the floor and the controls.
A heavier-duty thermostat or a load module will not help here. They allow a larger connected load, not better temperature monitoring.
Does the thermostat protect against a floor that is too hot?
That depends on the model and how it is set up. A thermostat that only measures air temperature does not monitor the floor. For temperature-sensitive floors, use the floor probe: the thermostat then controls on floor temperature, or on air temperature with a maximum floor temperature as a limit.
Place the probe between two heating cables so it measures the average floor temperature, not the temperature right next to one cable. Bear in mind that a probe measures in one spot. A covered area further away can get warmer without the thermostat noticing. A good layout plan and sensible use are still needed.
How hot can the floor get?
There is no single maximum for every floor. Check the instructions for every layer: floor finish, underlay, adhesive and heating. Many vinyl and laminate floors, for example, have a maximum surface temperature of 27 °C. A limit for the floor surface is not the same as the reading on a probe that sits deeper in the floor. For the right settings, read the best temperature for bathroom underfloor heating.
| Floor finish | What to check |
|---|---|
| Tiles | Adhesive, grout and build-up suitable for the chosen system |
| Vinyl/LVT | Approved heating type, temperature limit and adhesive instructions |
| Laminate | Approval for electric heating and thermal resistance with the underlay |
| Wood | Maximum temperature and guidance on moisture and warm-up |
| Carpet | Combined thermal resistance (tog value) of carpet and underlay |
"Suitable for underfloor heating" on the packaging is a starting point. Also check that electric underfloor heating and your floor build-up are specifically approved.
Is electric underfloor heating safe in a bathroom?
Yes, with a system designed for it. Heating mats with a waterproof cable are suitable for wet rooms, heating foil is not. The thermostat position, electrical protection and waterproof build-up must also be right. The heating does not replace tanking.
Have your electrician check the bathroom zones under BS 7671 and the protection. The heating circuit needs 30 mA RCD protection, and in England work in a bathroom is usually notifiable under Part P. Read more in our guide how to wire electric underfloor heating, or see our solutions for the bathroom.
What do CE, UKCA and approval marks mean?
With a CE or UKCA mark, the manufacturer declares that the product meets the applicable requirements. UKCA is the British counterpart of CE. Neither is an independent test of your complete floor. Ask for the declaration of conformity and clear installation instructions as well. If a product carries an extra approval mark, such as BEAB, check exactly which product and which properties were tested. An approved thermostat says nothing about a different mat, and a safe product can still be installed badly.
When should you switch the heating off?
Do you smell burning, see discolouration around the thermostat, feel unusual local heat, or does a breaker keep tripping? Switch the heating off and have the cause investigated before using it again. If there is smoke or fire, leave the room and call 999.
Do not keep resetting an RCD or MCB. A device that trips is a signal to investigate, not a problem you solve by fitting a bigger one.
Choosing safely starts with the right system
Not sure about your floor build-up or the connection? Get in touch with us and we will be happy to help.