Menu
EUR
Nu 10% korting op het hele assortiment! Gebruik code: BLACK10 *Niet geldig op Magnum-producten
Is electric underfloor heating enough as the only bathroom heating?

Is electric underfloor heating enough as the only bathroom heating?

By: H.G. Voortman Comments: 0

Yes, in many bathrooms electric underfloor heating can completely replace the radiator. There must be enough unobstructed floor area for the heating mat, the room must be reasonably well insulated, and you need to choose the right output. For most bathrooms, that means 150 watts per square metre.

That is the short answer. What matters in practice is knowing when this does and does not apply. Below, we explain how to make an initial assessment for your bathroom without needing an installer to do it for you.

What really matters for electric bathroom underfloor heating

Almost everyone focuses on watts per square metre because that is the number on the packaging. Yet this alone does not determine whether your bathroom will get warm. What heats the room is the total output: watts per square metre multiplied by the area of heating mat you can actually install.

The second factor is often underestimated. You do not install a mat beneath the toilet, vanity unit, bath or shower tray. In an 8 m² bathroom, there may be only 4 to 5 m² of clear floor. You buy 5 m² of heating rather than 8 m², significantly reducing the total output. This is why two equally sized bathrooms can need very different solutions.

What output does your bathroom need?

Three common power ratings are available, each serving a different purpose.

Output Suitable for Application
100 W/m² A comfortably warm floor Comfort heating alongside an existing heat source
150 W/m² Heating the whole room Primary heating, the most popular choice
200 W/m² Extra-fast warm-up Limited clear floor area or moderate insulation

100 W/m²: for comfort only

Do you already have a radiator that heats the bathroom, and mainly want to avoid cold tiles? Then 100 watts per square metre is sufficient. It makes the floor pleasantly warm, but is almost always insufficient as the bathroom's only heat source.

150 W/m²: the standard for primary heating

This is the most popular option, with good reason. At 150 watts per square metre, you can heat a bathroom without unnecessarily increasing energy use. For a reasonably insulated bathroom with enough clear floor area, it is usually the right choice. Find suitable systems in our range of electric bathroom underfloor heating.

200 W/m²: when space or insulation is limited

200 watts per square metre is useful in two situations: a bathroom with many fixtures and little clear floor, or a room with moderate insulation, extensive external walls or a large window through which more heat escapes. The higher output compensates for the shortfall. It is usually unnecessary in a well-insulated bathroom with ample floor area.

[products=badkamer_vloerverwarming_blog]

Worked example: is 150 W/m² enough for your bathroom?

This calculation takes two minutes and quickly shows whether your proposed system is adequate.

Step 1. Work out the clear floor area. Draw your bathroom and subtract everything beneath which no mat will be installed: toilet, vanity unit, bath, shower tray and fixed cupboards. Also leave a strip of roughly 10 cm along the walls.

Step 2. Estimate the heat requirement. Bathrooms are generally kept warmer than other rooms. Allow approximately 100 watts per square metre of room area in a well-insulated home, and 125 watts or more in an older home with moderate insulation.

Step 3. Compare the figures. Consider an 8 m² bathroom in a house built in 2005, with 5 m² of clear floor:

  • Heat requirement: 8 × 100 = approximately 800 watts
  • Output at 150 W/m²: 5 × 150 = 750 watts
  • Output at 200 W/m²: 5 × 200 = 1,000 watts

Here, 150 watts per square metre falls just short, so 200 watts is the more suitable option. If the same bathroom has 6 m² of clear floor, the output is 900 watts, comfortably exceeding the estimate.

As a rule of thumb, 150 watts per square metre is usually sufficient if you can heat around two-thirds of the bathroom floor. If less is available, consider 200 watts per square metre or insulation beneath the mat. This is an indication, not a formal heat-loss calculation. If in doubt, assess your situation with our selection guide.

Insulation: a cost-effective way to make better use of the output

Before choosing a more powerful system, consider a step that often achieves more: insulation beneath the mat. Without insulation, some heat escapes down into the subfloor. A 6 or 10 mm board helps direct heat upwards. The floor heats faster and less energy is lost during use.

This is particularly valuable for a ground-floor bathroom, above a crawl space, or on a concrete floor that absorbs heat. It can make the difference between a system that is slightly inadequate and one that works comfortably. Adding insulation is often a wiser investment than increasing the power rating.

[products=xps_isolatieplaten]

When electric underfloor heating is insufficient as the only bathroom heating

Some bathrooms simply leave too little capacity for electric underfloor heating to be the sole heat source. Pay particular attention to:

  • An attic bathroom with sloping walls and a roof window: little floor space and substantial heat loss.
  • A small bathroom filled with fixtures, leaving very little clear floor.
  • An older home with single glazing or uninsulated external walls.
  • A bathroom with a large bath occupying much of the floor.

In these cases, underfloor heating can still provide comfort, but as supplementary heating rather than a replacement.

Heating a bathroom without a radiator requires a different approach

This is rarely mentioned, yet it strongly affects satisfaction. A radiator responds quickly: turn it on and you feel warmth within about ten minutes. A heated floor must first warm up itself before the room follows. Depending on the floor construction, this can take 20 to 60 minutes.

If electric underfloor heating is your only heat source, a programmable Wi-Fi thermostat is therefore essential. Schedule the floor to warm up half an hour before your alarm and again before your evening shower. You get warmth when needed without heating all day. Read our article about the ideal temperature for electric bathroom underfloor heating for suitable settings.

Which option suits your bathroom?

If you mainly want a warm floor and already have a radiator, 100 watts per square metre is sufficient. If you want to heat the whole bathroom without a radiator and have enough clear floor, 150 watts per square metre is usually the right choice. Where clear floor is limited or insulation is moderate, consider 200 watts per square metre, potentially combined with insulation.

Electric underfloor heating can therefore make the bathroom radiator unnecessary in many cases. It frees up wall space and provides more even warmth than a single heat source. Preparation is key: establish the clear floor area and match the output to it.

Still unsure whether to choose 100, 150 or 200 watts per square metre? Browse our electric bathroom underfloor heating, calculate your requirements with the selection guide, or contact us. A few minutes of calculation helps avoid installing too little capacity or buying unnecessary material.


Comments (0)

There are no comments yet, be the first one to comment
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
Order for another €150,00 and receive free shipping
0
Compare
Start comparison

Leave a comment

Your email address will not be published
This product has been added to your cart